Made of high strength aluminum with Mil-Spec Type III hard coat anodized finishFeatures a non-glare coating to reduce reflectionsMakes the A3 rifle compatible with the Clawgear AUG HandguardFeatures a 30 slot picatinny rail (NATO STANAG 4694)Anti-rotational QD attachment point at the front

Clawgear‘s modular mounting system products are designed to increase weapon performance and handling. Due to it‘s construction in 6082 Aluminum, this rugged and high quality item will serve you in any combat situation.NATO STANAG 4694 RAILThe 13 slot Picatinny Rail allows the user to upgrade his 55X rifle with various aiming devices or accessories.LIGHTWEIGHT CONSTRUCTIONAlthough this mount base has been designed in a lightweight way, its mechanical strength is not being affected.ADJUSTMENT SCREWIt clamps the mount for a solid fit between both attachment points on the receiver and is secured by a clamp screw on the left side.DOVETAIL SLOTThe front attachment point is the dovetail on the receiver which is normally used to fix the brass catcher.CompatibilitySIG550, SIG551, SIG552, SIG553, PE90 and all variants of the rifle with standard adjustable diopter sights.InstallationMake sure your weapon is unloaded and safe. Screw the included adjustment screw fully into the mount base. Put the rail on the upper receiver and slide it forward so the dovetail on the receiver connects smoothly to the front of the rail. Then use a 8mm wrench to unscrew the adjustment screw until it moves inside the hole of the rear sight base. Tighten it up for a solid fit. Use the clamp screw on the left side of the mount base to secure its position.

Claw Gear‘s modular firearms accessories products are designed to increase weapon performance and accuracy. Due to it‘s outstanding materials construction, this rugged and high quality Austrian made item will serve you in any combat situation.NATO STANAG 4694 RailThe nine slot Picatinny rail allows the user to upgrade his AK rifle with various aiming devices or accessories.Adjustment ScrewsAdjust the angle of the mount to align it with the point of bullet impact.Shaped ContourThe design fits to the curve on the receiver cover and even allows to dissable the rifle without dismounting the AK RSM.Emergency SightEven with an optical device mounted the sight can be used as a backup.Compatibility: AK-47, AKM, RPK, AK-74 and all variants with the original Mauser-type adjustable rear sight. Not compatible with SKS rifles.Installation: Dismount the existing rear sight and leaf spring. Put the AK RSM into the guidance on the rear sight base and align both holes. Punch the included roll pin into the bore so it is flush with both sides. Insert the big set screw on top into the middle thread on the rail and tighten it until the emergency sight aims to the point of impact. Finally insert both small set screws into the forward threads and tighten them stoutly. Warning: Torque for setscrew max. 3 NM

Clawgear‘s modular firearms accessories products are designed to increase weapon performance and accuracy. Due to it‘s outstanding materials construction, this rugged and high quality Austrian made item will serve you in any combat situation.NATO STANAG 4694 RailThe 10 slot Picatinny rail allows the user to upgrade his Modular Scope Mount equipped AUG rifle with additional accessories.SurfaceHigh alloy aluminium with anodized coating (MIL-8625-F type III, class II) for heavy use.This rails fits the AUG Modular Scope Mount (Art.Nr. 20114)

Picatinny Rail for M-LOKFeature List:• Picatinny Rail for M-LOK interface with 5 slots.• Made from hight strength aluminium and a durablehard coat anodized finish, that meets Mil specrequirements.• Mounting hardware included (Nuts and Screws), withstainless steel T Nuts to avoid corrosion. Nocoating that can wear off or chip away when mountedand dismounted several times.Note:When mounting the Rail and tightening the screws, be sure not to overtighten them.The proper torque specs are max. 4Nm or 35in/lb.Tip: Use the short handle of the Allen key for tightening.

Clawgear’s nylon equipment is designed to increase the operator's performance. These products are optimized to be as versatile and lightweight as possible. The use of bonded Reinforced materials same time massively increases the durability and lifetime maintaining a low weight.The Raider Two Point Sling is a classic length adjustable two-point sling. Both sling ends have an adjustable 25mm webbing loop for attaching various sling swivels or hooks. The sling is being adjusted with a known and proven steel cam buckle. The middle part of the sling is padded, increasing user comfort during long wear.Features:Fully adjustable Two-point SlingPull Tab for fast length adjustmentAdjustable Webbing loops at each sling endDifferent mounting options can be added at each sling endStiff Nylon WebbingCenter Section Padded for improved comfortCompatible with all Clawgear Front/Rear End KitsFabrics:25mm NylonWebbingWoojin and ITW Nexus plastic partsSteel Cam buckle

The radio pouch is designed to fit AN/PRC-152, AN/PRC-148, and other similarly sized handheld radios. The pocket can be opened to easily access the screen and buttons without removing the radio device. The pouch is closed and secured using a reliable polymer buckle and two velcro-padded shock cords. The bottom has a zipper for easy battery access.The pouch consists of two main parts - a mounting plate and the radio compartment.The mounting part is manufactured of a 500D Nylon base fitted with two aluminum tubes that guarantee rigid construction. It has two PALS straps for easy attachment to virtually any PALS-based vest, backpack, or other gear-carrying systems. An extra side strap with a polymer buckle helps furtherly stabilize the pouch to maximize comfort and performance.The radio compartment is made from the same 500D Nylon, foam, and durable laminate. The device in the pouch is secured in its place with a shock cord. Utilized materials guarantee extreme robustness and resistance to physical and typical "deployment" damage with full access to all control knobs. The bottom-placed zipper is used for battery replacement in the field without removing the radio from the pouch.Both parts are sewn together at the bottom and connected with a pull tab on top. This allows the pouch to pivot outward for quick and easy access to the screen and buttons. Additional loops of double-sided velcro on the sides grant an easy way to secure and organize cables connecting the radio with the PTT button or other small items like chemlights.Fabrics:500D NylonTacticoat ReinforcedNylon WebbingYKK ZippersWooJin BucklesDimensions:Height: 24cmWidth: 9cmDepth: 5cmPALS space: 2 X 3 (minimal) 2 X 4 (optimal).