Clawgear finally brings a versatile and lightweight low profile handguard to the Steyr AUG and same time also introduces M-LOK and Keymod platform to this weapon system. Sophisticated engineered and fully field tested for uncompromising fightability and operator-friendliness. Solid one piece construction, made of hard coated aluminium (Mil-8625-F type III, class II) for perfect combination of low weight and highest mechanical stability. The AUG M-LOK handguard features twelve mounting slots for limitless versatility and does not interfere with most silencers and muzzle devices. Compatibility:Steyr AUG A1/A2, AUG A3 SF, AUG P, AUG Z, AUG LMG variants, AUG SA variants, MSAR STG-556.Does not fit AUG A3, AUG Z A3, AUG 9mm variants

• Matt black non-glare surface coating to reduce reflections• QD sling attachment point on the rear side of the handguard• M-LOK mounting system to fit all types of M-LOK accessories: rails, vertical grips, AFG, ...• Fits a wide variety of AK 47‘s with stamped and milled receivers• Lightweight construction made out of high strength 6061 aluminium with MIL-SPEC type III hardcoat anodize finish

• Matt black non-glare surface coating to reduce reflections• QD sling attachment point on the rear side of the handguard• M-LOK mounting system to fit all types of M-LOK accessories: rails, vertical grips, AFG, ...• Fits a wide variety of AK 47‘s with stamped and milled receivers with a front sling loop on the gasblock• Lightweight construction made out of high strength 6061 aluminium with MIL-SPEC type III hardcoat anodize finish

• Matt black non-glare surface coating to reduce reflections• QD sling attachment point on the rear side of the handguard• M-LOK mounting system to fit all types of M-LOK accessories: rails, vertical grips, AFG, ...• Fits a wide variety of AK 47‘s with stamped and milled receivers with a front sling loop on the gasblock• Lightweight construction made out of high strength 6061 aluminium with MIL-SPEC type III hardcoat anodize finish

Picatinny Rail for M-LOK with QD mounting pointFeature List:• Picatinny Rail for M-LOK interface with 10 slots•Integrated QD mounting for Sling Swivel• Made from hight strength aluminium and a durablehard coat anodized finish, that meets Mil specrequirements.• Mounting hardware included (Nuts and Screws), withstainless steel T Nuts to avoid corrosion. Nocoating that can wear off or chip away when mountedand dismounted several times.Note:When mounting the Rail and tightening the screws, be sure not to overtighten them.The proper torque specs are max. 4Nm or 35in/lb.Tip: Use the short handle of the Allen key for tightening if no Torque Wrench is avalible

Claw Gear‘s modular firearms accessories products are designed to increase weapon performance and accuracy. Due to it‘s outstanding materials construction, this rugged and high quality made item will serve you in any situation.B&T Quick DetachAllows the operator to enhance the weapon system with B&T QD (Rotex V) suppressors.Breacher SpikesThese sharp and hardened steel spikes allow the user to destroy barriers in CQB situations.Mounting NotchesTwelve mounting grooves allow the compensator to fit on any AK based weapon system.Expansion ChamberThe construction guides the exhaust gases in optimal direction to reduce recoil and muzzle flip.Compatibility: AK-47, AKM, RPK, AK-74 and all variants based on these models with 14x1 LH muzzle thread. Does not fit on AK-100 Series, AKS-74U, Saiga rifles.Installation: Dismount existing muzzle devices and clean the thread surface. After applying a drop of oil on the thread, screw the compensator counterclockwise on the barrel and push the locking pin on the front sight base completely flat. Screw the compensator tight and release the locking pin into the next mounting notch available. Before using a silencer make sure the compensator is not moving at all.